PCIe C5 - I210 card connected on Lane 2 and 4 not detected in Jetson AGX Orin
Hi,
We have 4 I210 connected on C5 through the bridge. But we are able to see only 2 out of that on lspci.
I210 connected on Lane 6 and 7 are detected whereas I210 connected on Lane 2 and 4 are not detected.
We also followed the debug steps for PCIe Link-up failure which is mentioned in the document “JetsonModuleAdaptationAndBringUp”. But still facing the same issue.
Attached the log of “sudo lspci -vvv” and “sudo dmesg | grep pcie”
lspci
0000:00:00.0 PCI bridge: NVIDIA Corporation Device 229c (rev a1)
0000:01:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 229e (rev a1)
0001:01:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 229a (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:01.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:04.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:05.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:06.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:02:07.0 PCI bridge: PLX Technology, Inc. PEX 8734 32-lane, 8-Port PCI Express Gen 3 (8.0GT/s) Switch (rev ab)
0005:06:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
0005:07:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
Configuration from the file → kernel_tegra234-p3701-0004-p3737-0000.dtb
pcie@141a0000 {
compatible = “nvidia,tegra234-pcie\0snps,dw-pcie”;
power-domains = <0x02 0x05>;
reg = <0x00 0x141a0000 0x00 0x20000 0x00 0x3a000000 0x00 0x40000 0x00 0x3a040000 0x00 0x40000 0x00 0x3a080000 0x00 0x40000 0x2b 0x30000000 0x00 0x10000000>;
reg-names = “appl\0config\0atu_dma\0dbi\0ecam”;
status = “okay”;
#address-cells = <0x03>;
#size-cells = <0x02>;
device_type = “pci”;
num-lanes = <0x08>;
num-viewport = <0x08>;
linux,pci-domain = <0x05>;
clocks = <0x02 0xe1 0x02 0xea>;
clock-names = “core\0core_m”;
resets = <0x02 0x82 0x02 0x81>;
reset-names = “apb\0core”;
interrupts = <0x00 0x35 0x04 0x00 0x36 0x04>;
interrupt-names = “intr\0msi”;
interconnects = <0x44 0xe2 0x44 0xe3>;
interconnect-names = “dma-mem\0dma-mem”;
iommus = <0x03 0x14>;
iommu-map = <0x00 0x03 0x14 0x1000>;
msi-parent = <0x35 0x14>;
msi-map = <0x00 0x35 0x14 0x1000>;
dma-coherent;
iommu-map-mask = <0x00>;
#interrupt-cells = <0x01>;
interrupt-map-mask = <0x00 0x00 0x00 0x00>;
interrupt-map = <0x00 0x00 0x00 0x00 0x01 0x00 0x35 0x04>;
nvidia,dvfs-tbl = <0xc28cb00 0xc28cb00 0xc28cb00 0xc28cb00 0xc28cb00 0xc28cb00 0xc28cb00 0x27ac4000 0xc28cb00 0xc28cb00 0x27ac4000 0x5f5e1000 0xc28cb00 0x27ac4000 0x5f5e1000 0x7f22ff40>;
nvidia,max-speed = <0x04>;
nvidia,disable-aspm-states = <0x0f>;
nvidia,controller-id = <0x02 0x05>;
nvidia,tsa-config = <0x200b004>;
nvidia,disable-l1-cpm;
nvidia,aux-clk-freq = <0x13>;
nvidia,preset-init = <0x05>;
nvidia,aspm-cmrt = <0x3c>;
nvidia,aspm-pwr-on-t = <0x14>;
nvidia,aspm-l0s-entrance-latency = <0x03>;
nvidia,bpmp = <0x02 0x05>;
nvidia,aspm-cmrt-us = <0x3c>;
nvidia,aspm-pwr-on-t-us = <0x14>;
nvidia,aspm-l0s-entrance-latency-us = <0x03>;
bus-range = <0x00 0xff>;
ranges = <0x81000000 0x00 0x3a100000 0x00 0x3a100000 0x00 0x100000 0x82000000 0x00 0x40000000 0x2b 0x28000000 0x00 0x8000000 0xc3000000 0x27 0x40000000 0x27 0x40000000 0x03 0xe8000000>;
nvidia,cfg-link-cap-l1sub = <0x1c4>;
nvidia,cap-pl16g-status = <0x174>;
nvidia,cap-pl16g-cap-off = <0x188>;
nvidia,event-cntr-ctrl = <0x1d8>;
nvidia,event-cntr-data = <0x1dc>;
nvidia,dl-feature-cap = <0x30c>;
nvidia,ptm-cap-off = <0x318>;
vddio-pex-ctl-supply = <0x36>;
phys = <0x37 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e>;
phy-names = “p2u-0\0p2u-1\0p2u-2\0p2u-3\0p2u-4\0p2u-5\0p2u-6\0p2u-7”;
vpcie3v3-supply = <0x3f>;
vpcie12v-supply = <0x40>;
phandle = <0x377>;
};
dmesg.txt (5.4 KB)
lspci.txt (76.8 KB)