Using 4-Port PCI-express SATA 3 Card(su sa3034a) with Jetson Nano

Hello, @WayneWWW

I’m using 4-Port PCI-express SATA 3 Card.

product URL : Interface Cards: SSU SATA 3 III 4-Port PCI-e Card, [SU-SA3034A] - Plug & Play for Windows / Mac / Linux, with Low Profile - Australia Computer Online

I have tested above sata3card with Nano, XNX(jetpack4.6.2) on Jetson Nano devkit carrier board.

In Nano, The following error message appears, the monitor does not output, and booting does not work properly.
asmedia_pcie_bus_error.log (1.1 MB)

In XNX, You can check /dev/sda* as below and you can also mount it.

manager@manager-desktop:~$ ls /dev/sda*

/dev/sda  /dev/sda1

manager@manager-desktop:~$ ls /mnt/C/

bin   dev  home  lost+found  mnt  proc        root  sbin  srv  tmp  var

boot  etc  lib   media       opt  README.txt  run   snap  sys  usr

Could you tell me how to recognize sata disks with this sata3card in Nano?

Below is the execution result of lspci command in jetson nano, jetpack version, and nv_boot_control.conf information.

manager@manager-desktop:~$ lspci

00:01.0 PCI bridge: NVIDIA Corporation Device 0fae (rev a1)

00:02.0 PCI bridge: NVIDIA Corporation Device 0faf (rev a1)

01:00.0 SATA controller: ASMedia Technology Inc. Device 1064 (rev 02)

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 19)

manager@manager-desktop:~$ cat /etc/nv_tegra_release

# R32 (release), REVISION: 7.2, GCID: 30192233, BOARD: t210ref, EABI: aarch64, DATE: Wed Apr 20 21:34:48 UTC 2022

manager@manager-desktop:~$ cat /etc/nv_boot_control.conf

TNSPEC 3448-400-0002-J.0-1-0-jetson-nano-devkit-emmc-mmcblk0p1

COMPATIBLE_SPEC 3448-300-0002--1--jetson-nano-devkit-emmc-

TEGRA_CHIPID 0x21

TEGRA_OTA_BOOT_DEVICE /dev/mmcblk0boot0

TEGRA_OTA_GPT_DEVICE /dev/mmcblk0boot1

lspci -vvvv

01:00.0 SATA controller: ASMedia Technology Inc. Device 1064 (rev 02) (prog-if 01 [AHCI 1.0])

        Subsystem: ZyDAS Technology Corp. Device 2116

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
        Latency: 0

        Interrupt: pin A routed to IRQ 405

        Region 0: Memory at 13080000 (32-bit, non-prefetchable) [size=8K]

        Region 5: Memory at 13082000 (32-bit, non-prefetchable) [size=8K]

        [virtual] Expansion ROM at 13000000 [disabled] [size=512K]

        Capabilities: [40] Power Management version 3

                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+

                Address: 00000000ffeff000  Data: 0000

        Capabilities: [80] Express (v2) Endpoint, MSI 00

                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W

                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+

                        MaxPayload 128 bytes, MaxReadReq 512 bytes

                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

                LnkCap: Port #0, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us

                        ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+

                LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk+

                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

                LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

                DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported

                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled

                LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis+

                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

                         Compliance De-emphasis: -6dB

                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-

                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

        Capabilities: [100 v1] Advanced Error Reporting

                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

                AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

        Capabilities: [130 v1] #19

        Kernel driver in use: ahci

Attach dmesg.
dmesg_nano.txt (86.2 KB)

Thank you.